BD-165101

thumbnail
thumbnail

BD-165101


 ※← Please click here for ‘Detail of the Data’.
 

Note*1: ‘Data’ indicates the specifications while aluminum board (size: 57*57*5t) is attached to the motor flange.
Please see ‘Detail of the Data’ above for more information.

Note*2:Gearhead and/or encoder can be mounted to the motor as option. Please see the specifications below for more information.

 

马达特性

项目 单位
极数 Pole 2
工作电压 V 12 ± 5%
线圈电阻 Ω 7
扭矩 mN-m/A 15.2
逆起电压 V/K rpm 1.59
无负载转速 rpm 7500 (Note*1)
最大工作电流 A 0.76 (Note*1)
最大工作转矩 mNm 11.3 (Note*1)
定额回转速度 rpm 3480 (Note*1)
定额输出 W 4.1 (Note*1)
转动惯量 g・cm2 1.1
重量 g 60
驱动器 BSD-36-****
(Max speed)
0512-△ 014
( 5000 rpm )

Note*1: This value depends on a specification of driver and encoder.

Note*2: The maximum speed of the standard type driver, BSD-36 Series, is 5,000 rpm but it can be customized to over 5,000 rpm. Please send us “Inquiry Form” or “Special Order Form” on Contact Page for more details on custom order.

Note*3: Only for two(2) pole motor can be combined with an optical encoder. BD-165101 can be combined with Optical Encoder: PC1000. Please see “高分辨率编码器 (可选)” below for the specification of PC1000.

 

 

编码器 (可选)

检测方式 磁性检测
项目 单位 编码器特性
工作电压 V cc DC +5V±7%
工作电流 mA 30
输出电压 V High ≧ 3.5 Low ≦ 1.0
最大输出电流 mA 10 (max.)
频道 ch 3 (A,B,Z)
最高响应频率 kHz 700
输出脉冲数 Can use Line Driver Output and/or TTL Output
输出脉冲数 Pulse/Rev 512

 

高分辨率编码器 (可选)


检测方式 光学检测
项目 单位 编码器特性
工作电压 V cc DC +5V±5%
工作电流 mA 60 (max.)
输出电压   V High ≧ 4.0(min.) Low ≦ 0.5(max.)
频道 ch 3
最高响应频率 kHz 100 (max.)
输出脉冲数 Pulse/Rev 1000

 

ZJP 系列 行星减速器 (可选)



Rated Characteristic of Motor with Gear(s)
BD-165101G ZJP 1/xxx

減速比 4 6 16 24 36 64 96 ※144 ※216 256 ※384 ※576 ※864 ※1296
最大工作转矩 N・m 0.036 0.054 0.116 0.174 0.26 0.369 0.553 0.58 0.58 1.186 1.2 1.2 1.2 1.2
定额回转速度 rpm 870 580 218 145 97 54 36 24 16 14 9 6 4 3
定额输出 W 3.3 3.3 2.6 2.6 2.6 2.1 2.1 1.5 1 1.7 1.1 0.8 0.5 0.3
尺寸 L1 mm 19.4 19.4 22.9 22.9 22.9 28.2 28.2 28.2 28.2 33.5 33.5 33.5 33.5 33.5

Note*1: If using deceleration ratios marked with an asterisk (*), please make sure not to exceed the allowable output torque of the gearhead.

Note*2: These are the values in uniform load.

Page Top